It’s finally time to start the Ceramics 3D-Printer build! This is going to be an exiting project where I expect to learn a lot. In this first part of the series I go over my initial design and thoughts on how to build and get the 3D-Printer working like it should
I get a lot of tips and tricks from the internet and I would like to give a special thanks to Vormvrij and their Lutum 3D-printer for inspiration. Please take a look at their website:
https://lutum.vormvrij.nl/
Also thanks to Stoneflower3d for use of image:
www.stoneflower3d.com
Links to parts I use in this build, please let me know if you are looking for something else or if some of the links are dead:
.:|Electronics and control|:.
Nema 42 Planetary Reduction Gear selectable Ratio:
http://bit.ly/2H4RuMw
Nema 17 Extruder Gear Stepper Motor Selectable Ratio:
http://bit.ly/2Kzc4Xn
Rampas 1.4 Controller + Mega2560 R3 + 12864 Display with Limit Switch & A4988 Stepper Motor Driver:
http://bit.ly/33DiEUe
Nema17 59Ncm 2A 1.8°4-lead 48mm:
http://bit.ly/2z1RKHG
.:|Aluminium Extrusions|:.
Machifit BLACK 2020 V-Slot Aluminum Profile Extrusion:
http://bit.ly/2YRFDw6
Machifit SILVER 2020 V-Slot Aluminum Profile Extrusion:
http://bit.ly/2KLqVNl
Machifit BLACK 2040 V-Slot Aluminum Profile Extrusion:
https://bit.ly/2WplCuO
Machifit SILVER 2040 V-Slot Aluminum Profile Extrusion:
http://bit.ly/302uLs4
Machifit Black 2060 V-Slot Aluminum Profile Extrusion:
https://bit.ly/2HyPFbw
Machifit SILVER 2060 V-Slot Aluminum Profile Extrusion:
http://bit.ly/31HCKep
Machifit Black 2080 V-Slot Aluminum Profile Extrusion:
https://bit.ly/2wfmp2Y
Machifit SILVER 2080 V-Slot Aluminum Profile Extrusion:
http://bit.ly/33zQn11
.:|Aluminium Profile Accessories|:.
Machifit 2020L L Shape Corner Connector:
https://bit.ly/2HxbQyA
Drillpro 50pcs M5 T Sliding Nut Aluminum Profile:
https://bit.ly/2Hxr1YC
Machifit Aluminium Angle Corner Joint 90 Degree Corner Bracket:
https://bit.ly/2JWEL0M
Machifit 5 Holes Aluminum Profile Corner Bracket 90 Degree:
https://bit.ly/2JXBdLz
Inside Corner Connector Joint Bracket for Aluminum Profile:
https://bit.ly/2JA1osy
.:|Aluminium plates|:.
300x100x6mm ALUMINUM 6061 Flat Bar:
https://ebay.to/2N0XhXn
Community:
Website: https://goo.gl/9wZcs1
Instagram: https://goo.gl/1TnxKW
Facebook: https://goo.gl/H7L72E
Patreon: https://goo.gl/5pm5qs
Twitter: https://goo.gl/fzWWcA
3 thoughts on “DIY Ceramics 3D Printer (part 1) – Design and plan | CLAY | Pottery”
Thanks for finally talking about > DIY Ceramics 3D Printer (part 1) – Design and plan |
CLAY | Pottery | Willys Garage Norway < Loved it!
Thanks 🙂